Adlink Hurricane-QM57 User Manual

SME-LEMT-R0V8 Revision 0.8 / March 12 © LiPPERT ADLINK TECHNOLOGY GmbH Hans-Thoma-Str. 11 D-68163 Mannheim ht

SME-LEMT-R0V8 Revision 0.8 Page 6 of 22 Board Information This sections shows general information over the Board such as Name, CPU included onbo

SME-LEMT-R0V8 Revision 0.8 Page 7 of 22 4.2 The User Flash Memory Tab Memory For memory organization, refer to chapter 3 (Flash Memory Organi

SME-LEMT-R0V8 Revision 0.8 Page 8 of 22 Each line contains the address of the first byte of this line, followed by 16 data bytes (displayed as h

SME-LEMT-R0V8 Revision 0.8 Page 9 of 22 4.3 Hardware Control Tab

SME-LEMT-R0V8 Revision 0.8 Page 10 of 22 Watchdog The watchdog timeout value is given in seconds and can be set to 1-65535 seconds. A setting of

SME-LEMT-R0V8 Revision 0.8 Page 11 of 22 4.4 Hardware Monitor

SME-LEMT-R0V8 Revision 0.8 Page 12 of 22 Hardware Monitor and Logging The Hardware Monitor Tab shows a graphical representation of the current b

SME-LEMT-R0V8 Revision 0.8 Page 13 of 22 5 Command Line Interface The LEMT command line interface is available for both Linux and Windows versi

SME-LEMT-R0V8 Revision 0.8 Page 14 of 22  Any combination of parameters is allowed. If only one value is requested (e.g. pwrcycles) the output

SME-LEMT-R0V8 Revision 0.8 Page 15 of 22 5.5 Backlight Control The LEMT command line interface can be used to enable, disable or adjust LVDS ba

SME-LEMT-R0V8 Revision 0.8 Software Manual LEMT LiPPERT Document: SME-LEMT-R0V8.doc Revision 0.8 Copyright © 2008-2012 LiPPERT ADLINK TECHNOLOG

SME-LEMT-R0V8 Revision 0.8 Page 16 of 22 6 EAPI - Embedded Application Programming Interface The EAPI specification provides a common programmi

SME-LEMT-R0V8 Revision 0.8 Page 17 of 22 EApiStorageCap()  EApiStorageAreaRead()  EApiStorageAreaWrite()  EAPI Watchdog No Event Timeout EApi

SME-LEMT-R0V8 Revision 0.8 Page 18 of 22 7 LEMT Web Interface 7.1 Overview The LEMT web interface allows to remote access all main LEMT functi

SME-LEMT-R0V8 Revision 0.8 Page 19 of 22 7.2 Security Caution Running a web server may introduce several and severe security risks for your

SME-LEMT-R0V8 Revision 0.8 Page 20 of 22 7.3 Installation Windows XP or Windows 7 To install the LEMTWeb utility under Windows XP or Windows 7

SME-LEMT-R0V8 Revision 0.8 Page 21 of 22 tricky to set up and beyond the scope of this document. See e.g. man thttpd to avoid cutting the server

SME-LEMT-R0V8 Revision 0.8 Page 22 of 22 Alternatively you could set LEMT_COMMAND to "sudo lemt" and add a suitable entry for the web

SME-LEMT-R0V8 Revision 0.8 Page A Contact Information Headquarters LiPPERT ADLINK TECHNOLOGY GmbH Hans-Thoma-Straße 11 68163 Mannheim Germany P

SME-LEMT-R0V8 Revision 0.8 Page B Getting Help Should you have technical questions that are not covered by the respective manuals, please contac

SME-LEMT-R0V8 Revision 0.8 Page C Additional Information CoreExpress™ http://www.CoreExpress.c om Intel® Atom™ http://www.intel.com/products/c

SME-LEMT-R0V8 Revision 0.8 i Table of Contents 1 Overview 1 1.1 Introduction ...

SME-LEMT-R0V8 Revision 0.8 Page D Revision History Filename Date Edited by Change SME-LEMT-R0V1 2008-07-22 MH Draft SME-LEMT-R0V2 2008-07-28 MH

SME-LEMT-R0V8 Revision 0.8 ii 7 LEMT Web Interface 18 7.1 Overview ...

SME-LEMT-R0V8 Revision 0.8 Page 1 of 22 1 Overview 1.1 Introduction More and more boards from LiPPERT ADLINK TECHNOLOGY GmbH are assembled wit

SME-LEMT-R0V8 Revision 0.8 Page 2 of 22 2 Installation 2.1 Requirements  LiPPERT Board with LEMT  LEMTGui needs the QT Library at version

SME-LEMT-R0V8 Revision 0.8 Page 3 of 22 3 Flash Memory Organization The LEMT microcontroller provides 512, respectively 1024 bytes (depending o

SME-LEMT-R0V8 Revision 0.8 Page 4 of 22 3.3 Secure Data The secure data area is empty by factory default and may be protected against write acc

SME-LEMT-R0V8 Revision 0.8 Page 5 of 22 4 Graphical User Interface The graphical interface is available for Windows and Linux operating systems