Adlink cPCI-3615 User Manual

Advance Technologies; Automate the World.Manual Rev.: 2.01Revision Date: June 13, 2012Part No: 50-15077-1010cPCI-3615 Series3U CompactPCI® Dual-Cor

xThis page intentionally left blank.

86 BIOS Setup8.3.6 AHCI ConfigurationYou can use this screen to select options for the AHCI Settings.Use the up and down < Arrow > keys to selec

BIOS Setup 87cPCI-36158.3.7 Remote Access ConfigurationRemote access configuration provides the settings to allow remoteaccess by another computer to

88 BIOS SetupSerial Port ModeSelect the baud rate you want the serial port to use for consoleredirection. The options are 115200 8,n,1; 57600 8,n,1; 1

BIOS Setup 89cPCI-36158.4 Advanced PCI/PnP SettingsSelect the PCI/PnP tab from the setup screen to enter the Plugand Play BIOS Setup screen. You can

90 BIOS Setup8.5 Boot SettingsSelect the Boot tab from the setup screen to enter the Boot BIOSSetup screen. You can select any of the items in the lef

BIOS Setup 91cPCI-36158.5.1 Boot Settings ConfigurationUse this screen to select options for the Boot Settings Configura-tion. Use the up and down &l

92 BIOS Setup8.6 Security SetupPassword SupportTwo Levels of Password ProtectionProvides both a Supervisor and a User password. If you useboth passwor

BIOS Setup 93cPCI-3615Remember the PasswordKeep a record of the new password when the password ischanged. If you forget the password, you must erase

94 BIOS Setup8.7 Chipset SetupSelect the Chipset tab from the setup screen to enter the ChipsetBIOS Setup screen. You can select any of the items in t

BIOS Setup 95cPCI-36158.8 Exit MenuSelect the Exit tab from the setup screen to enter the Exit BIOSSetup screen. You can display an Exit BIOS Setup o

List of Figures xicPCI-3615List of FiguresFigure 1-1: cPCI-3615 Series Functional Block Diagram... 3Figure 4-1: cPCI-3615 Blade Board

96 BIOS SetupDiscard ChangesSelect Discard Changes from the Exit menu and press < Enter >.Select Ok to discard changes.Load Optimal DefaultsAuto

Important Safety Instructions 97cPCI-3615Important Safety InstructionsFor user safety, please read and follow all instructions,WARNINGS, CAUTIONS, a

98 Important Safety InstructionsX Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.A Lithium-type battery

Getting Service 99cPCI-3615Getting ServiceContact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jia

100 Getting ServiceADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12

xii List of FiguresThis page intentionally left blank.

List of Tables xiiicPCI-3615List of TablesTable 4-1: cPCI-3615 Front Panel System LED Descriptions ... 24Table 4-2: USB Connector Pin Definition

xiv List of TablesThis page intentionally left blank.

Introduction 1cPCI-36151 Introduction1.1 OverviewThe cPCI-3615 Series is a 3U CompactPCI single board computerin single-slot (4HP), dual-slot (8HP) o

2Introduction1.2 FeaturesX 3U CompactPCI blade in 4HP, 8HP or 12HP width form factorX Supports Dual-Core or Single-Core Intel® Atom™ processor, up to

Introduction 3cPCI-36151.3 Block DiagramFigure 1-1: cPCI-3615 Series Functional Block DiagramDB-3610L2 DB-3UMC J2FRONTPANELRGB USB 1/2 DMI COM1, KB/M

4Introduction1.4 Product ListProducts in the cPCI-3615 Series include:Processor BladeX cPCI-3615: 4HP width (single-slot) 3U CompactPCI featur-ing Ato

Introduction 5cPCI-36151.5 Package Contents The cPCI-3615 is packaged with the following components. If anyof the items on the contents list are miss

Revision HistoryRevision Release Date Description of Change(s)2.00 2011/04/29 Initial release2.01 2012/06/13Correct Atom N455 frequency, board layout;

6IntroductionThis page intentionally left blank.

Specifications 7cPCI-36152 Specifications2.1 cPCI-3615 SpecificationsCompactPCI® Standards• PICMG® 2.0 CompactPCI® Rev. 3.0• PICMG® 2.1 Hot Swap Spec

8 Specifications1. Hard drive limits operational vibration. When application requireshigher vibration specification, it is recommended to use a flash

Specifications 9cPCI-36152.2 I/O Connectivity Table1. Software switchable from front port(s).FunctioncPCI-3615(4HP)cPCI-3615D(8HP)cPCI-3615P(12HP)cPC

10 Specifications2.3 Power RequirementsIn order to guarantee stable operation of the system, it is recom-mended that significantly more power be provi

Specifications 11cPCI-3615Power ConsumptionThis section provides information on the power consumption ofcPCI-3615 Series when using Intel® Atom™ proc

12 SpecificationsThis page intentionally left blank.

Functional Description 13cPCI-36153 Functional DescriptionThe following sections describe the cPCI-3615 Series featuresand functions.3.1 ProcessorThe

14 Functional DescriptionX Micro-FCBGA8 packaging technologiesX Thermal management support via Intel® Thermal Monitor 1 (TM1) and Intel® Thermal Monit

Functional Description 15cPCI-3615The following list outlines the key features of system memory support:X One channel DDR3 memoryX Memory DDR3 data t

Preface iiicPCI-3615PrefaceCopyright 2011-12 ADLINK Technology Inc.This document contains proprietary information protected by copy-right. All rights

16 Functional Description3.2 ChipsetIntel® ICH8 Mobile I/O Controller HubThe ICH8M provides extensive I/O support. Functions and capa-bilities include

Functional Description 17cPCI-36153.4 BatteryThe cPCI-3615 is provided with a 3.0V “coin cell” lithium batteryfor the Real Time Clock (RTC). The batt

18 Functional DescriptionThis page intentionally left blank.

Board Interfaces 19cPCI-36154 Board InterfacesThis chapter illustrates the board layout, connector pinassignments, and jumper settings to familiarize

20 Board Interfaces4.2 cPCI-3615 Blade Assembly LayoutThis section describes the final assembly layout of the single slotcPCI-3615 (4HP).Figure 4-2: c

Board Interfaces 21cPCI-36154.3 cPCI-3615D Blade Assembly LayoutThe dual-slot width cPCI-3615D (8HP) is comprised of thecPCI-3615 single-slot main bo

22 Board Interfaces4.4 cPCI-3615P Blade Assembly LayoutThe triple-slot width cPCI-3615P (12HP) is comprised of thecPCI-3615D dual-slot assembly and th

Board Interfaces 23cPCI-36154.5 cPCI-3615 Series Front Panel LayoutFigure 4-4: cPCI-3615, cPCI-3615D Front Panel Layout1212cPCI-3615cPCI-3615DVGAGbE

24 Board InterfacesFigure 4-5: cPCI-3615P Front Panel LayoutOptional 2-slot version with PMC/XMC as shown below is avail-able by request. Please conta

Board Interfaces 25cPCI-36154.6 cPCI-R3610T RTM Board LayoutFigure 4-6: cPCI-R3610T RTM Board LayoutCOM2/3 COM ports LAN Dual Ethernet portSATA1/2 SA

iv PrefaceUsing this ManualAudience and ScopeThe cPCI-3615 User’s Manual is intended for hardwaretechnicians and systems operators with knowledge of i

26 Board Interfaces4.7 cPCI-R3610(T) RTM Front PanelFigure 4-7: cPCI-R3610(T) RTM Front Panel12VGACOM3 USB GbE x2 COM2

Board Interfaces 27cPCI-36154.8 Connector Pin AssignmentsUSB ConnectorsTable 4-2: USB Connector Pin DefinitionVGA Connector (DB-15)Table 4-3: VGA Con

28 Board InterfacesGigabit Ethernet Connectors (RJ-45)Table 4-4: GbE Connector Pin DefinitionsTable 4-5: Ethernet Status LED DefinitionsPin #10BASE-T/

Board Interfaces 29cPCI-3615PS/2 Keyboard/Mouse ConnectorTable 4-6: PS/2 Keyboard/Mouse Connector Pin DefinitionSerial Port DB-9 Connector (COM1)Tabl

30 Board InterfacescPCI-R3610(T) Serial Port Pin Header (COM2/3)Table 4-8: cPCI-R3610(T) Serial Port Pin Header DefinitionSerial ATA Connectors on RTM

Board Interfaces 31cPCI-3615Serial ATA Connector on DB-3610L2Table 4-10: Serial ATA Connector on DB-3610L2 Pin DefinitionPin # SignalS1 GNDS2 TX+S3 T

32 Board InterfacesCompactFlash Connector on DB-3610CFTable 4-11: CompactFlash Connector Pin DefinitionSignal Name Pin# Pin# Signal NameGND 1 26 GNDDD

Board Interfaces 33cPCI-3615DB-3610CF Connector (CN2)Table 4-12: DB-3610CF Connector Pin DefinitionSignal Name Pin # Pin # Signal NameIDE_D7 1 2 IDE_

34 Board InterfacesDB-3610L2 Connector (CN4)Table 4-13: DB-3610L2 Connector Pin DefinitionSignal Name Pin # Pin # Signal NameUSB2-N 1 2 -12VUSB2-P 3 4

Board Interfaces 35cPCI-3615DB-3UMC Connector (CN7)Table 4-14: DB-3UMC Connector Pin DefinitionSignal Name Pin # Pin # Signal NameNC 1 2 -12VNC 3 4 +

Preface vcPCI-3615ConventionsTake note of the following conventions used throughout thismanual to make sure that users perform certain tasks andinstr

36 Board InterfacesPMC Connector (JN1/2)Table 4-15: PMC Connector Pin DefinitionsPin# JN1 Signal JN2 Signal1 PMC_TCK P12V2 N12V PMC_TRST-L3 GND PMC_TM

Board Interfaces 37cPCI-3615Table 4-15: PMC Connector Pin Definitions (cont’d)Pin# JN1 Signal JN2 Signal33 PCIX_FRAME-L GND34 GND NC35 GND PCIX_TRDY-

38 Board InterfacesXMC Connector (JN3)Table 4-16: XMC Connector Pin DefinitionPin# A B C D E F1 RXP RXN 3.3V NC NC VPWR2 GND GND Not used GND GND PCIE

Board Interfaces 39cPCI-3615CompactPCI J1 ConnectorTable 4-17: CompactPCI J1 Connector Pin DefinitionPin Z A B C D E F25 GND +5V REQ64# ENUM# +3.3V +

40 Board InterfacesCompactPCI J2 ConnectorTable 4-18: CompactPCI J2 Connector Pin DefinitionPin Z A B C D E F22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6

Board Interfaces 41cPCI-36154.9 Switch and Jumper SettingsClear CMOS Switch (SW4)The cPCI-3615 comes with a Clear CMOS switch to reset theCMOS values

42 Board InterfacesCOM1 Mode Selection Switches (SW1~SW4)These switches select COM1 (cPCI-3615D/P front panel) to beRS-232 full modem, RS-422, RS-485,

Board Interfaces 43cPCI-3615COM2 Mode Selection Switches on RTM (SW1~SW4)These switches on the RTM select COM2 to be RS-232 fullmodem, RS-422, RS-485

44 Board InterfacesCOM3 Mode Selection Switches on RTM (SW5~SW8)These switches on the RTM select COM3 to be RS-232 fullmodem, RS-422, RS-485, or RS-48

Board Interfaces 45cPCI-3615XMC VPWR Select Jumper on DB-3UMC (JPX1)This jumper is located on the DB-3UMC board near JN1/2 andselects the XMC VPWR se

vi PrefaceThis page intentionally left blank.

46 Board InterfacesThis page intentionally left blank.

Getting Started 47cPCI-36155 Getting StartedThis chapter describes the installation procedures for thecPCI-3615 and rear transition module:X 2.5” SAT

48 Getting Started5.2 Hard Drive InstallationThe cPCI-3615D/P 2/3 slot versions provide space to install a slimtype 2.5” Serial-ATA hard drive.Install

Getting Started 49cPCI-36153. Secure the hard drive assemby to the cPCI-3615D usingfour M2.5 screws provided.

50 Getting StartedInstalling a Hard Drive - cPCI-3615P1. To install a hard drive on the cPCI-3615P, the front paneland DB-3UMC daughter board must fir

Getting Started 51cPCI-36152. Detach the faceplate from the PCB assembly.3. Loosen the five screws securing DB-3UMC riser card tothe PCB assembly.

52 Getting Started4. Remove the DB-3UMC riser card, taking care to lift itfrom the board-to-board connector indicated below.5. Attach the mounting bra

Getting Started 53cPCI-36156. Align the hard drive assemby with the mounting pointson the cPCI-3615P and insert it into the onboard SerialATA connect

54 Getting Started8. Re-attach the DB-3UMC riser card to the PCB assembly,taking care to press down firmly on the board-to-boardconnector.9. Re-attach

Getting Started 55cPCI-36155.3 PMC/XMC Card InstallationThe cPCI-3615P provides one PMC/XMC slot designed to support3.3V or 5V V(I/O) (default 3.3V)

viicPCI-3615Table of ContentsRevision History... iiPreface...

56 Getting Started2. Remove the DB-3UMC daughter board by unscrewingthe four screws as shown below.3. There is a 3.3V key on board by default, if the

Getting Started 57cPCI-36155. Secure the PMC/XMC card to the DB-3UMC by attach-ing four screws (provided with the card) from the under-side of the da

58 Getting Started7. Secure the PMC/XMC assembly to the DB-3610L2 risercard using the four screws removed in Step 2 above.8. Remove the PMC filler fac

Getting Started 59cPCI-36155.4 Removing the DB-3610CF Daughter BoardTo access SW1 (VGA/GPIO Mode Switch) which is under theDB-3610CF Daughter Board,

60 Getting Started3. Remove the screw securing the DB-3610CF from thecomponent side of the blade as shown.4. Remove the screw securing the DB-3610CF f

Getting Started 61cPCI-36156. Remove the six screws securing the heatsink to theblade assembly7. Remove the heatsink to access SW1.To reassemble the

62 Getting Started5.5 Installing the cPCI-3615 to the ChassisThe cPCI-3615 may only be installed in a system slot of a 3UCompactPCI chassis. These ins

Getting Started 63cPCI-36155.6 RTM Installation - cPCI-R3610(T)The installation and removal procedures for a RTM are the sameas those for CompactPCI

64 Getting StartedThis page intentionally left blank.

Driver Installation 65cPCI-36156 Driver InstallationThe cPCI-3615 drivers are available from the ADLINK All-In-OneCD at X:\cPCI\cPCI-3615\, or from t

viii4.5 cPCI-3615 Series Front Panel Layout ... 234.6 cPCI-R3610T RTM Board Layout... 2

66 Driver InstallationThis page intentionally left blank.

Utilities 67cPCI-36157 Utilities7.1 Watchdog TimerThis section describes the operation of the cPCI-3615’s watchdogtimer (WDT). The primary function o

68 UtilitiesSample CodeThe sample program written in C shown below offers an interac-tive way to test the Watchdog Timer under DOS.#include<stdio.h

Utilities 69cPCI-3615outportb(IT8783_ioPort, 0x02);outportb(IT8783_ioPort+1, 0x02);}//Check chipvoid Get_IT8783_ID(unsigned int &ID1, unsigned in

70 Utilitiesoutportb(IT8783_ioPort+1, registerValue);outportb(IT8783_ioPort, 0xCD);registerValue = inportb(IT8783_ioPort + 1);registerValue |= 0x01;

Utilities 71cPCI-3615tempCount++;if(tempCount > 65535)tempCount = 65535;printf("WDT timeout in %d minutes.\n", tempCount);}else{outportb

72 Utilities7.2 Preboot Execution Environment (PXE)The cPCI-3615 Series supports the Intel® Preboot ExecutionEnvironment (PXE) that is capable of boot

BIOS Setup 73cPCI-36158 BIOS SetupThe following chapter describes basic navigation for theAMIBIOS®8 BIOS setup utility.8.1 Starting the BIOSTo enter

74 BIOS SetupSetup MenuThe main BIOS setup menu is the first screen that you can navi-gate. Each main BIOS setup menu option is described in thisuser’

BIOS Setup 75cPCI-3615Note: There is a hot key legend located in the right frame on most setup screens.The < F8 > key on your keyboard is the

ixcPCI-36158.5 Boot Settings ... 908.5.1 Boot Settings Configuration...

76 BIOS SetupF10 The < F10 > key allows you to save any changes you have made and exit Setup. Press the < F10 > key to save your changes.

BIOS Setup 77cPCI-36158.2 Main SetupWhen you first enter the Setup Utility, you will enter the Main setupscreen. You can always return to the Main se

78 BIOS Setupthe left frame of the screen to go to the sub menu for that item.You can display an Advanced BIOS Setup option by highlighting itusing th

BIOS Setup 79cPCI-36158.3.1 CPU ConfigurationYou can use this screen to select options for the CPU Configura-tion Settings. Use the up and down <

80 BIOS SetupExecute-Disable Bit Capability Intel’s Execute Disable Bit functionality can help prevent cer-tain classes of malicious buffer overflow a

BIOS Setup 81cPCI-36158.3.2 IDE ConfigurationYou can use this screen to select options for the IDE ConfigurationSettings. Use the up and down < Ar

82 BIOS Setup8.3.3 Super IO ConfigurationYou can use this screen to select options for the Super IO settings.Use the up and down < Arrow > keys

BIOS Setup 83cPCI-36158.3.4 Hardware Health ConfigurationThis option displays the current status of all of the monitored hard-ware devices/components

84 BIOS Setup8.3.5 USB ConfigurationYou can use this screen to select options for the USB Configura-tion. Use the up and down < Arrow > keys to

BIOS Setup 85cPCI-3615X Auto: This option auto detects USB Keyboards or Mice and if found, allows them to be utilized during boot and while using DOS